Winmodem problem with SUSE 9.0 Pro

[Ermis]

Akolouthontas ta vimata tou odigou pou mou ypodeiksate gia tous 
smartlink drivers, synantisa ta eksis:

1. Boot the SUSE LINUX system and log in as a user.

ok

    2. Open a console and enter the command "sux -".

ok

    3. When prompted, enter the administrator password.

ok

    4. Enter the command yast -i smartlink-softmodem to install a 
background service needed for the SmartLink driver with YaST.

ok

    5. Leave the console open and, in the YaST Control Center, select 
System -> Editor for /etc/sysconfig Files.

ok

    6. In the tree structure to the left, select Hardware -> Modem -> 
SLMODEMD_DEVICE.

den ipirxe kan i epilogi Modem

    7. In this section, select the entry SLMODEMD_COUNTRY. If necessary, 
replace the data in the input field with the land in which you are 
located. For example, the entry for Germany is GERMANY. To view a 
complete list of supported countries, enter the command slmodemd 
--countrylist.

des vima 6

    8. If you have an internal modem, skip the following step and 
continue with step 10.

piga sto vima 10

    9. If you have a USB modem, select the entry SLMODEMD_DEVICE in the 
opened section and replace the data in the input field with slusb0.
   10. Click Finish and confirm the following change list with OK.

ok

   11. Change to the console and enter the following two commands in the 
indicated order:
           * insserv -d slmodemd

insserv: slmodemd: No such file or directory

           * /etc/init.d/slmodemd start

bash: /etc/init.d/slmodemd: No such file or directory

   12. Close the console by pressing the key combination [CTRL]+[D] twice.

ok

   13. Change back to the YaST Control Center and select Network Devices 
-> Modem.

ok

   14. If you have already configured your modem with YaST, delete this 
information including the provider data under Change... and terminate 
the configuration dialog. Then reopen the modem configuration in the 
YaST Control Center.

ok

   15. Even if your modem is detected, selact Other (not detected) and 
click Configure....

ok

   16. In Modem device, enter /dev/ttySL0 manually.

ok, me tin diafora oti to /dev/ttySL0 to ekana copy apo ton odigo kai 
den to pliktrologisa

   17. Click Details.

ok

   18. Set Baud rate to 115200.

ok

   19. Click OK then Next.

ok

   20. From this point, perform the settings as described in the User 
Guide from page 99, last paragraph.

   ok

results from yasts's hardware info:

PCI 1f.6: 0703 Modem (Generic)
   [Created at pci.65]
   Unique ID: ORVU.wuCrdJaLnzF
   Hardware Class: modem
   Model: "Acer Incorporated [ALI] 82801DB AC'97 Modem Controller"
   Vendor: pci 0x8086 "Intel Corporation"
   Device: pci 0x24c6 "82801DB AC'97 Modem Controller"
   SubVendor: pci 0x1025 "Acer Incorporated [ALI]"
   SubDevice: pci 0x0064
   Revision: 0x03
   I/O Ports: 0x2400-0x24ff (rw)
   I/O Ports: 0x2000-0x207f (rw)
   IRQ: 10 (159 events)
   Config Status: cfg=yes, avail=yes, need=no, active=unknown