Provlima me USB printer & mass storage camera (kernel 2.6.5)

Wed Apr 28 21:14:08 EEST 2004

Xaireto kai pali!

To provlima me to hotplug diorthothike, egkatestisa kainourgio paketo
hotplug apo to ftp.suse.com ston katalogo people/kraxel

To problima me ton printer paramenei, opoios mporei na voithisei as
kanei reply:)

Nikos

On Wed, 2004-04-28 at 17:04, Centaur wrote: 
> Xaireto tous sinlistes linuxious!
> 
> Prosfata ekana compile ton kainourgio kernel 2.6.5 se mia dianomi SUSE
> 9.0. Exo ftiaxei ta perissotera pragmata, mono me diskoleyei ligo i
> egkatastasi toy USB ektipoti mou HP-930C kai tis psifiakis hotplug
> kameroulas mou Fuji Finepix. Tha sas eksigiso to provlima:
> 
> 1. Eno exo kanei compile se modules tin USB Support (lege me uhci_hcd,
> ehci_hcd, ohci_hcd), apo ta opoia ta dyo prota fortonontai sto boot. Eno
> oi siskeyes fainontai na anagnorizontai (checkara me ena utility lsusb
> poy egkatestisa - akomi kai sto SuSeplugger) ...
> 
> Gia ton ektipoti :
> 
> ->egkatestisa ksana CUPS 1.1.20 kai filtro apo tin Hewlett Packard hijs
> 1.6 --> o opoios fortonei kanonika ( mporo na kano administration tasks
> kai apo to web interface tou scheduler & apo KDE Print Manager)
> 
> TO PROBLHMA: "no such device usb:/dev/lp0"
> 
> Gia tin mass storage kameroula:
> 
> -> Fainetai sto Suseplugger ALLA den mporo na katalavo pou sto kalo
> einai egkatestimeni, diladi den mporo na kano mount giati den vrisko pou
> einai sto /dev
> 
> Prospathisa /dev/sda1 ... 5, /dev/sdb1 .. 5 tipota!
> 
> PROBLIMA: Den mporo na tin kano mount :(
> 
> Pithanon i lisi na einai apli, spao to kefali mou kai den mporo na ti
> vro.
> 
> Ti lete na ftaiei ? Siggnomi gia to makroskeles tou email. Akolouthoun
> KERNEL MESSAGES kai Kernel Boot mesg.
> 
> Y.G: Ti apegine to kanali linux-gr sto IRCNet i to GRNET opou ginontan
> oraies sizitisoules palaiotera?
> 
> Eyxaristo gia tin ora sas!
> 
> Nikos
> 
> KERNEL MESSAGES RCHOTPLUG START
> 
> Initializing USB Mass Storage driver...
> usb-storage 3-1:1.0: usb_probe_interface
> usb-storage 3-1:1.0: usb_probe_interface - got id
> usb-storage: USB Mass Storage device detected
> usb-storage: altsetting is 0, id_index is 11
> usb-storage: -- associate_dev
> usb-storage: Vendor: Fujifilm
> usb-storage: Product: FinePix 1400Zoom
> usb-storage: Transport: Control/Bulk/Interrupt
> usb-storage: Protocol: Uniform Floppy Interface (UFI)
> usb-storage: Endpoints: In: 0xc87b75c0 Out: 0xc87b75d4 Int: 0xc87b75e8
> (Period 1)
> usb-storage: *** thread sleeping.
> scsi4 : SCSI emulation for USB Mass Storage devices
> usb-storage: queuecommand called
> usb-storage: *** thread awakened.
> usb-storage: Faking INQUIRY command
> usb-storage: scsi cmd done, result=0x0
> usb-storage: *** thread sleeping.
>  Vendor: Fujifilm Model: FinePix 1400Zoom Rev: 0100
>  Type: Direct-Access ANSI SCSI revision: 02
> Attached scsi generic sg1 at scsi4, channel 0, id 0, lun 0, type 0
> usb-storage: queuecommand called
> usb-storage: *** thread awakened.
> usb-storage: Bad target number (1:0)
> usb-storage: scsi cmd done, result=0x40000
> usb-storage: *** thread sleeping.
> usb-storage: queuecommand called
> usb-storage: *** thread awakened.
> usb-storage: Bad target number (2:0)
> usb-storage: scsi cmd done, result=0x40000
> usb-storage: *** thread sleeping.
> usb-storage: queuecommand called
> usb-storage: *** thread awakened.
> usb-storage: Bad target number (3:0)
> usb-storage: scsi cmd done, result=0x40000
> usb-storage: *** thread sleeping.
> usb-storage: queuecommand called
> usb-storage: *** thread awakened.
> usb-storage: Bad target number (4:0)
> usb-storage: scsi cmd done, result=0x40000
> usb-storage: *** thread sleeping.
> usb-storage: queuecommand called
> usb-storage: *** thread awakened.
> usb-storage: Bad target number (5:0)
> usb-storage: scsi cmd done, result=0x40000
> usb-storage: *** thread sleeping.
> usb-storage: queuecommand called
> usb-storage: *** thread awakened.
> usb-storage: Bad target number (6:0)
> usb-storage: scsi cmd done, result=0x40000
> usb-storage: *** thread sleeping.
> usb-storage: queuecommand called
> usb-storage: *** thread awakened.
> usb-storage: Bad target number (7:0)
> usb-storage: scsi cmd done, result=0x40000
> usb-storage: *** thread sleeping.
> USB Mass Storage device found at 3
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: registered
> new driver usb-storage
> USB Mass Storage support registered.
> 
> KERNEL BOOT MESSAGES
> Adding 1028152k swap on /dev/hdf3. Priority:42 extents:1
> found reiserfs format "3.6" with standard journal
> Reiserfs journal params: device hdf1, size 8192, journal first block 18,
> max trans len 1024, max batch 900, max commit age 30, max trans age 30
> reiserfs: checking transaction log (hdf1) for (hdf1)
> Using r5 hash to sort names
> NTFS driver 2.1.6 [Flags: R/W MODULE].
> NTFS volume version 3.1.
> NTFS volume version 3.1.
> NTFS volume version 3.1.
> hdg: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
> Uniform CD-ROM driver Revision: 3.20
> hdh: ATAPI 32X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
> SCSI subsystem initialized
> scsi0 : SCSI host adapter emulation for IDE ATAPI devices
>  Vendor: IOMEGA Model: ZIP 100 Rev: 05.H
>  Type: Direct-Access ANSI SCSI revision: 00
> hdg: CHECK for good STATUS
> hdh: CHECK for good STATUS
> Real Time Clock Driver v1.12
> ip_tables: © 2000-2002 Netfilter core team
> ip_conntrack version 2.1 (4095 buckets, 32760 max) - 296 bytes per
> conntrack
> 8139too Fast Ethernet driver 0.9.27
> eth0: RealTek RTL8139 at 0xe1ac6000, 00:20:ed:50:04:b8, IRQ 18
> eth0: Identified 8139 chip type 'RTL-8100B/8139D'
> eth0: link down
> NET: Registered protocol family 17
> ieee1394: Initialized config rom entry `ip1394'
> ohci1394: $Rev: 1172 $ Ben Collins <bcollins at debian.org>
> ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16]
> MMIO=[e2008000-e20087ff] Max Packet=[2048]
> ieee1394: raw1394: /dev/raw1394 device initialized
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: registered
> new driver usbfs
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: registered
> new driver hub
> ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
> ehci_hcd 0000:00:10.3: VIA Technologies, Inc. USB 2.0
> ehci_hcd 0000:00:10.3: reset hcs_params 0x3206 dbg=0 cc=3 pcc=2 ordered
> !ppc ports=6
> ehci_hcd 0000:00:10.3: reset hcc_params 6872 thresh 7 uframes
> 256/512/1024
> ehci_hcd 0000:00:10.3: capability 0001 at 68
> ehci_hcd 0000:00:10.3: irq 21, pci mem e1ae4000
> ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:00:10.3: reset command 080002 (park)=0 ithresh=8
> period=1024 Reset HALT
> ehci_hcd 0000:00:10.3: init command 010009 (park)=0 ithresh=1 period=256
> RUN
> ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29
> ehci_hcd 0000:00:10.3: root hub device address 1
> usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/message.c: USB
> device number 1 default language ID 0x409
> usb usb1: Product: VIA Technologies, Inc. USB 2.0
> usb usb1: Manufacturer: Linux 2.6.5 ehci_hcd
> usb usb1: SerialNumber: 0000:00:10.3
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
> usb usb1: registering 1-0:1.0 (config #1, interface 0)
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
> hub 1-0:1.0: usb_probe_interface
> hub 1-0:1.0: usb_probe_interface - got id
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 6 ports detected
> hub 1-0:1.0: standalone hub
> hub 1-0:1.0: ganged power switching
> hub 1-0:1.0: individual port over-current protection
> hub 1-0:1.0: Single TT
> hub 1-0:1.0: TT requires at most 8 FS bit times
> hub 1-0:1.0: Port indicators are not supported
> hub 1-0:1.0: power on to power good time: 20ms
> hub 1-0:1.0: hub controller current requirement: 0mA
> hub 1-0:1.0: local power source is good
> hub 1-0:1.0: no over-current condition exists
> hub 1-0:1.0: enabling power on all ports
> ieee1394: Host added: ID:BUS[0-00:1023] GUID[000020ed00501d18]
> ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
> ohci_hcd: block sizes: ed 64 td 64
> USB Universal Host Controller Interface driver v2.2
> uhci_hcd 0000:00:10.0: VIA Technologies, Inc. USB
> uhci_hcd 0000:00:10.0: irq 21, io base 0000d400
> uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
> uhci_hcd 0000:00:10.0: detected 2 ports
> uhci_hcd 0000:00:10.0: root hub device address 1
> usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/message.c: USB
> device number 1 default language ID 0x409
> usb usb2: Product: VIA Technologies, Inc. USB
> usb usb2: Manufacturer: Linux 2.6.5 uhci_hcd
> usb usb2: SerialNumber: 0000:00:10.0
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
> usb usb2: registering 2-0:1.0 (config #1, interface 0)
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
> hub 2-0:1.0: usb_probe_interface
> hub 2-0:1.0: usb_probe_interface - got id
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> hub 2-0:1.0: standalone hub
> hub 2-0:1.0: unknown reserved power switching mode
> hub 2-0:1.0: individual port over-current protection
> hub 2-0:1.0: Port indicators are not supported
> hub 2-0:1.0: power on to power good time: 2ms
> hub 2-0:1.0: hub controller current requirement: 0mA
> hub 2-0:1.0: local power source is good
> hub 2-0:1.0: no over-current condition exists
> hub 2-0:1.0: enabling power on all ports
> uhci_hcd 0000:00:10.1: VIA Technologies, Inc. USB (#2)
> ehci_hcd 0000:00:10.3: GetStatus port 1 status 001803 POWER sig=j CSC
> CONNECT
> hub 1-0:1.0: port 1, status 501, change 1, 480 Mb/s
> uhci_hcd 0000:00:10.1: irq 21, io base 0000d800
> uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
> uhci_hcd 0000:00:10.1: detected 2 ports
> uhci_hcd 0000:00:10.1: root hub device address 1
> usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/message.c: USB
> device number 1 default language ID 0x409
> usb usb3: Product: VIA Technologies, Inc. USB (#2)
> usb usb3: Manufacturer: Linux 2.6.5 uhci_hcd
> usb usb3: SerialNumber: 0000:00:10.1
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
> usb usb3: registering 3-0:1.0 (config #1, interface 0)
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
> hub 3-0:1.0: usb_probe_interface
> hub 3-0:1.0: usb_probe_interface - got id
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> hub 3-0:1.0: standalone hub
> hub 3-0:1.0: unknown reserved power switching mode
> hub 3-0:1.0: individual port over-current protection
> hub 3-0:1.0: Port indicators are not supported
> hub 3-0:1.0: power on to power good time: 2ms
> hub 3-0:1.0: hub controller current requirement: 0mA
> hub 3-0:1.0: local power source is good
> hub 3-0:1.0: no over-current condition exists
> hub 3-0:1.0: enabling power on all ports
> uhci_hcd 0000:00:10.2: VIA Technologies, Inc. USB (#3)
> hub 1-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x501
> uhci_hcd 0000:00:10.2: irq 21, io base 0000dc00
> uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
> uhci_hcd 0000:00:10.2: detected 2 ports
> uhci_hcd 0000:00:10.2: root hub device address 1
> ehci_hcd 0000:00:10.3: port 1 full speed --> companion
> ehci_hcd 0000:00:10.3: GetStatus port 1 status 003801 POWER OWNER sig=j
> CONNECT
> ehci_hcd 0000:00:10.3: GetStatus port 2 status 001803 POWER sig=j CSC
> CONNECT
> hub 1-0:1.0: port 2, status 501, change 1, 480 Mb/s
> usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/message.c: USB
> device number 1 default language ID 0x409
> usb usb4: Product: VIA Technologies, Inc. USB (#3)
> usb usb4: Manufacturer: Linux 2.6.5 uhci_hcd
> usb usb4: SerialNumber: 0000:00:10.2
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
> usb usb4: registering 4-0:1.0 (config #1, interface 0)
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
> hub 4-0:1.0: usb_probe_interface
> hub 4-0:1.0: usb_probe_interface - got id
> hub 4-0:1.0: USB hub found
> hub 4-0:1.0: 2 ports detected
> hub 4-0:1.0: standalone hub
> hub 4-0:1.0: unknown reserved power switching mode
> hub 4-0:1.0: individual port over-current protection
> hub 4-0:1.0: Port indicators are not supported
> hub 4-0:1.0: power on to power good time: 2ms
> hub 4-0:1.0: hub controller current requirement: 0mA
> hub 4-0:1.0: local power source is good
> hub 4-0:1.0: no over-current condition exists
> hub 4-0:1.0: enabling power on all ports
> hub 1-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x501
> ehci_hcd 0000:00:10.3: port 2 full speed --> companion
> ehci_hcd 0000:00:10.3: GetStatus port 2 status 003801 POWER OWNER sig=j
> CONNECT
> uhci_hcd 0000:00:10.1: port 1 portsc 008a
> hub 3-0:1.0: port 1, status 100, change 3, 12 Mb/s
> uhci_hcd 0000:00:10.1: port 2 portsc 008a
> hub 3-0:1.0: port 2, status 100, change 3, 12 Mb/s
> uhci_hcd 0000:00:10.0: port 1 portsc 009b
> hub 2-0:1.0: port 1, status 101, change 3, 12 Mb/s
> uhci_hcd 0000:00:10.0: port 1 portsc 0099
> uhci_hcd 0000:00:10.0: port 1 portsc 0099
> uhci_hcd 0000:00:10.0: port 1 portsc 0099
> uhci_hcd 0000:00:10.0: port 1 portsc 0099
> uhci_hcd 0000:00:10.0: port 1 portsc 0099
> hub 2-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x101
> usb 2-1: new full speed USB device using address 2
> usb 2-1: new device strings: Mfr=4, Product=3, SerialNumber=5
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/message.c: USB
> device number 2 default language ID 0x409
> usb 2-1: Product: HP ScanJet 4470c
> usb 2-1: Manufacturer: Hewlett-Packard
> usb 2-1: SerialNumber: CN1CJAC17PZ
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
> usb 2-1: registering 2-1:1.0 (config #1, interface 0)
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
> uhci_hcd 0000:00:10.0: port 2 portsc 009b
> hub 2-0:1.0: port 2, status 101, change 3, 12 Mb/s
> uhci_hcd 0000:00:10.0: port 2 portsc 0099
> uhci_hcd 0000:00:10.0: port 2 portsc 0099
> uhci_hcd 0000:00:10.0: port 2 portsc 0099
> uhci_hcd 0000:00:10.0: port 2 portsc 0099
> uhci_hcd 0000:00:10.0: port 2 portsc 0099
> hub 2-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x101
> usb 2-2: new full speed USB device using address 3
> usb 2-2: new device strings: Mfr=1, Product=2, SerialNumber=3
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/message.c: USB
> device number 3 default language ID 0x409
> usb 2-2: Product: DeskJet 930C
> usb 2-2: Manufacturer: Hewlett-Packard
> usb 2-2: SerialNumber: HU11G2G3B6JK
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
> usb 2-2: registering 2-2:1.0 (config #1, interface 0)
> /home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
> uhci_hcd 0000:00:10.1: port 1 portsc 0088
> hub 3-0:1.0: port 1 enable change, status 100
> uhci_hcd 0000:00:10.1: port 2 portsc 0088
> hub 3-0:1.0: port 2 enable change, status 100
> uhci_hcd 0000:00:10.2: port 1 portsc 008a
> hub 4-0:1.0: port 1, status 100, change 3, 12 Mb/s
> uhci_hcd 0000:00:10.2: port 2 portsc 008a
> hub 4-0:1.0: port 2, status 100, change 3, 12 Mb/s
> uhci_hcd 0000:00:10.2: port 1 portsc 0088
> hub 4-0:1.0: port 1 enable change, status 100
> uhci_hcd 0000:00:10.2: port 2 portsc 0088
> hub 4-0:1.0: port 2 enable change, status 100
> uhci_hcd 0000:00:10.1: suspend_hc
> uhci_hcd 0000:00:10.2: suspend_hc
> Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
> ip1394: $Rev: 1175 $ Ben Collins <bcollins at debian.org>
> ip1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
> ACPI: Power Button (FF) [PWRF]
> ACPI: Processor [CPU0] (supports C1 C2, 2 throttling states)
> PCI: Setting latency timer of device 0000:00:11.5 to 64
> apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
> apm: overridden by ACPI.
> nvidia: no version for "struct_module" found: kernel tainted.
> nvidia: module license 'NVIDIA' taints kernel.
> 0: nvidia: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-5336 Wed
> Jan 14 18:29:26 PST 2004
> agpgart: Unknown parameter `agp_try_unsupported'
> 0: NVRM: AGPGART: unable to retrieve symbol table
> Linux video capture interface: v1.00
> bttv: driver version 0.9.12 loaded
> bttv: using 8 buffers with 2080k (520 pages) each for capture
> bttv: Bt8xx card found (0).
> bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 19, latency: 32, mmio:
> 0xe2005000
> bttv0: detected: Leadtek WinFast TV 2000 [card=34], PCI subsystem ID is
> 107d:6606
> bttv0: using: Leadtek WinFast 2000/ WinFast 2000 XP
> [card=34,autodetected]
> bttv0: gpio: en=00000000, out=00000000 in=00bff707 [init]
> i2c-algo-bit.o: (0) scl=1, sda=1
> i2c-algo-bit.o: (1) scl=1, sda=0
> i2c-algo-bit.o: (2) scl=1, sda=1
> i2c-algo-bit.o: (3) scl=0, sda=1
> i2c-algo-bit.o: (4) scl=1, sda=1
> i2c-algo-bit.o: bt878 #0 [sw] passed test.
> bttv0: using tuner=5
> bttv0: i2c: checking for MSP34xx @ 0x80... not found
> bttv0: i2c: checking for TDA9875 @ 0xb0... not found
> bttv0: i2c: checking for TDA7432 @ 0x8a... not found
> tuner: chip found at addr 0xc2 i2c-bus bt878 #0 [sw]
> tuner: type set to 5 (Philips PAL_BG (FI1216 and compatibles)) by bt878
> #0 [sw]
> bttv0: registered device video0
> bttv0: registered device vbi0
> bttv0: registered device radio0
> bttv0: PLL: 28636363 => 35468950 .. ok
> bttv0: add subdevice "remote0"
> atkbd.c: Unknown key released (translated set 2, code 0x7a on
> isa0060/serio0).
> atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
> NET: Registered protocol family 4
> and so on .... 
> 
> 
> 