Provlima me USB printer & mass storage camera (kernel 2.6.5)

Wed Apr 28 17:04:03 EEST 2004

Xaireto tous sinlistes linuxious!

Prosfata ekana compile ton kainourgio kernel 2.6.5 se mia dianomi SUSE
9.0. Exo ftiaxei ta perissotera pragmata, mono me diskoleyei ligo i
egkatastasi toy USB ektipoti mou HP-930C kai tis psifiakis hotplug
kameroulas mou Fuji Finepix. Tha sas eksigiso to provlima:

1. Eno exo kanei compile se modules tin USB Support (lege me uhci_hcd,
ehci_hcd, ohci_hcd), apo ta opoia ta dyo prota fortonontai sto boot. Eno
oi siskeyes fainontai na anagnorizontai (checkara me ena utility lsusb
poy egkatestisa - akomi kai sto SuSeplugger) ...

Gia ton ektipoti :

->egkatestisa ksana CUPS 1.1.20 kai filtro apo tin Hewlett Packard hijs
1.6 --> o opoios fortonei kanonika ( mporo na kano administration tasks
kai apo to web interface tou scheduler & apo KDE Print Manager)

TO PROBLHMA: "no such device usb:/dev/lp0"

Gia tin mass storage kameroula:

-> Fainetai sto Suseplugger ALLA den mporo na katalavo pou sto kalo
einai egkatestimeni, diladi den mporo na kano mount giati den vrisko pou
einai sto /dev

Prospathisa /dev/sda1 ... 5, /dev/sdb1 .. 5 tipota!

PROBLIMA: Den mporo na tin kano mount :(

Pithanon i lisi na einai apli, spao to kefali mou kai den mporo na ti
vro.

Ti lete na ftaiei ? Siggnomi gia to makroskeles tou email. Akolouthoun
KERNEL MESSAGES kai Kernel Boot mesg.

Y.G: Ti apegine to kanali linux-gr sto IRCNet i to GRNET opou ginontan
oraies sizitisoules palaiotera?

Eyxaristo gia tin ora sas!

Nikos

KERNEL MESSAGES RCHOTPLUG START

Initializing USB Mass Storage driver...
usb-storage 3-1:1.0: usb_probe_interface
usb-storage 3-1:1.0: usb_probe_interface - got id
usb-storage: USB Mass Storage device detected
usb-storage: altsetting is 0, id_index is 11
usb-storage: -- associate_dev
usb-storage: Vendor: Fujifilm
usb-storage: Product: FinePix 1400Zoom
usb-storage: Transport: Control/Bulk/Interrupt
usb-storage: Protocol: Uniform Floppy Interface (UFI)
usb-storage: Endpoints: In: 0xc87b75c0 Out: 0xc87b75d4 Int: 0xc87b75e8
(Period 1)
usb-storage: *** thread sleeping.
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Faking INQUIRY command
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
 Vendor: Fujifilm Model: FinePix 1400Zoom Rev: 0100
 Type: Direct-Access ANSI SCSI revision: 02
Attached scsi generic sg1 at scsi4, channel 0, id 0, lun 0, type 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
USB Mass Storage device found at 3
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: registered
new driver usb-storage
USB Mass Storage support registered.

KERNEL BOOT MESSAGES
Adding 1028152k swap on /dev/hdf3. Priority:42 extents:1
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device hdf1, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (hdf1) for (hdf1)
Using r5 hash to sort names
NTFS driver 2.1.6 [Flags: R/W MODULE].
NTFS volume version 3.1.
NTFS volume version 3.1.
NTFS volume version 3.1.
hdg: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdh: ATAPI 32X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
SCSI subsystem initialized
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
 Vendor: IOMEGA Model: ZIP 100 Rev: 05.H
 Type: Direct-Access ANSI SCSI revision: 00
hdg: CHECK for good STATUS
hdh: CHECK for good STATUS
Real Time Clock Driver v1.12
ip_tables: © 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 296 bytes per
conntrack
8139too Fast Ethernet driver 0.9.27
eth0: RealTek RTL8139 at 0xe1ac6000, 00:20:ed:50:04:b8, IRQ 18
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
eth0: link down
NET: Registered protocol family 17
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1172 $ Ben Collins <bcollins at debian.org>
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16]
MMIO=[e2008000-e20087ff] Max Packet=[2048]
ieee1394: raw1394: /dev/raw1394 device initialized
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: registered
new driver usbfs
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: registered
new driver hub
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
ehci_hcd 0000:00:10.3: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.3: reset hcs_params 0x3206 dbg=0 cc=3 pcc=2 ordered
!ppc ports=6
ehci_hcd 0000:00:10.3: reset hcc_params 6872 thresh 7 uframes
256/512/1024
ehci_hcd 0000:00:10.3: capability 0001 at 68
ehci_hcd 0000:00:10.3: irq 21, pci mem e1ae4000
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.3: reset command 080002 (park)=0 ithresh=8
period=1024 Reset HALT
ehci_hcd 0000:00:10.3: init command 010009 (park)=0 ithresh=1 period=256
RUN
ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29
ehci_hcd 0000:00:10.3: root hub device address 1
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/message.c: USB
device number 1 default language ID 0x409
usb usb1: Product: VIA Technologies, Inc. USB 2.0
usb usb1: Manufacturer: Linux 2.6.5 ehci_hcd
usb usb1: SerialNumber: 0000:00:10.3
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
usb usb1: registering 1-0:1.0 (config #1, interface 0)
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times
hub 1-0:1.0: Port indicators are not supported
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: hub controller current requirement: 0mA
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: enabling power on all ports
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000020ed00501d18]
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. USB
uhci_hcd 0000:00:10.0: irq 21, io base 0000d400
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: detected 2 ports
uhci_hcd 0000:00:10.0: root hub device address 1
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/message.c: USB
device number 1 default language ID 0x409
usb usb2: Product: VIA Technologies, Inc. USB
usb usb2: Manufacturer: Linux 2.6.5 uhci_hcd
usb usb2: SerialNumber: 0000:00:10.0
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
usb usb2: registering 2-0:1.0 (config #1, interface 0)
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: unknown reserved power switching mode
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: Port indicators are not supported
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: hub controller current requirement: 0mA
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: enabling power on all ports
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. USB (#2)
ehci_hcd 0000:00:10.3: GetStatus port 1 status 001803 POWER sig=j CSC
CONNECT
hub 1-0:1.0: port 1, status 501, change 1, 480 Mb/s
uhci_hcd 0000:00:10.1: irq 21, io base 0000d800
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: detected 2 ports
uhci_hcd 0000:00:10.1: root hub device address 1
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/message.c: USB
device number 1 default language ID 0x409
usb usb3: Product: VIA Technologies, Inc. USB (#2)
usb usb3: Manufacturer: Linux 2.6.5 uhci_hcd
usb usb3: SerialNumber: 0000:00:10.1
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
usb usb3: registering 3-0:1.0 (config #1, interface 0)
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: unknown reserved power switching mode
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: Port indicators are not supported
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: hub controller current requirement: 0mA
hub 3-0:1.0: local power source is good
hub 3-0:1.0: no over-current condition exists
hub 3-0:1.0: enabling power on all ports
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. USB (#3)
hub 1-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x501
uhci_hcd 0000:00:10.2: irq 21, io base 0000dc00
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: detected 2 ports
uhci_hcd 0000:00:10.2: root hub device address 1
ehci_hcd 0000:00:10.3: port 1 full speed --> companion
ehci_hcd 0000:00:10.3: GetStatus port 1 status 003801 POWER OWNER sig=j
CONNECT
ehci_hcd 0000:00:10.3: GetStatus port 2 status 001803 POWER sig=j CSC
CONNECT
hub 1-0:1.0: port 2, status 501, change 1, 480 Mb/s
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/message.c: USB
device number 1 default language ID 0x409
usb usb4: Product: VIA Technologies, Inc. USB (#3)
usb usb4: Manufacturer: Linux 2.6.5 uhci_hcd
usb usb4: SerialNumber: 0000:00:10.2
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
usb usb4: registering 4-0:1.0 (config #1, interface 0)
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: unknown reserved power switching mode
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: Port indicators are not supported
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: hub controller current requirement: 0mA
hub 4-0:1.0: local power source is good
hub 4-0:1.0: no over-current condition exists
hub 4-0:1.0: enabling power on all ports
hub 1-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x501
ehci_hcd 0000:00:10.3: port 2 full speed --> companion
ehci_hcd 0000:00:10.3: GetStatus port 2 status 003801 POWER OWNER sig=j
CONNECT
uhci_hcd 0000:00:10.1: port 1 portsc 008a
hub 3-0:1.0: port 1, status 100, change 3, 12 Mb/s
uhci_hcd 0000:00:10.1: port 2 portsc 008a
hub 3-0:1.0: port 2, status 100, change 3, 12 Mb/s
uhci_hcd 0000:00:10.0: port 1 portsc 009b
hub 2-0:1.0: port 1, status 101, change 3, 12 Mb/s
uhci_hcd 0000:00:10.0: port 1 portsc 0099
uhci_hcd 0000:00:10.0: port 1 portsc 0099
uhci_hcd 0000:00:10.0: port 1 portsc 0099
uhci_hcd 0000:00:10.0: port 1 portsc 0099
uhci_hcd 0000:00:10.0: port 1 portsc 0099
hub 2-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x101
usb 2-1: new full speed USB device using address 2
usb 2-1: new device strings: Mfr=4, Product=3, SerialNumber=5
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/message.c: USB
device number 2 default language ID 0x409
usb 2-1: Product: HP ScanJet 4470c
usb 2-1: Manufacturer: Hewlett-Packard
usb 2-1: SerialNumber: CN1CJAC17PZ
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
usb 2-1: registering 2-1:1.0 (config #1, interface 0)
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
uhci_hcd 0000:00:10.0: port 2 portsc 009b
hub 2-0:1.0: port 2, status 101, change 3, 12 Mb/s
uhci_hcd 0000:00:10.0: port 2 portsc 0099
uhci_hcd 0000:00:10.0: port 2 portsc 0099
uhci_hcd 0000:00:10.0: port 2 portsc 0099
uhci_hcd 0000:00:10.0: port 2 portsc 0099
uhci_hcd 0000:00:10.0: port 2 portsc 0099
hub 2-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x101
usb 2-2: new full speed USB device using address 3
usb 2-2: new device strings: Mfr=1, Product=2, SerialNumber=3
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/message.c: USB
device number 3 default language ID 0x409
usb 2-2: Product: DeskJet 930C
usb 2-2: Manufacturer: Hewlett-Packard
usb 2-2: SerialNumber: HU11G2G3B6JK
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
usb 2-2: registering 2-2:1.0 (config #1, interface 0)
/home/centaur/Documents/linux-2.6.5/drivers/usb/core/usb.c: usb_hotplug
uhci_hcd 0000:00:10.1: port 1 portsc 0088
hub 3-0:1.0: port 1 enable change, status 100
uhci_hcd 0000:00:10.1: port 2 portsc 0088
hub 3-0:1.0: port 2 enable change, status 100
uhci_hcd 0000:00:10.2: port 1 portsc 008a
hub 4-0:1.0: port 1, status 100, change 3, 12 Mb/s
uhci_hcd 0000:00:10.2: port 2 portsc 008a
hub 4-0:1.0: port 2, status 100, change 3, 12 Mb/s
uhci_hcd 0000:00:10.2: port 1 portsc 0088
hub 4-0:1.0: port 1 enable change, status 100
uhci_hcd 0000:00:10.2: port 2 portsc 0088
hub 4-0:1.0: port 2 enable change, status 100
uhci_hcd 0000:00:10.1: suspend_hc
uhci_hcd 0000:00:10.2: suspend_hc
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
ip1394: $Rev: 1175 $ Ben Collins <bcollins at debian.org>
ip1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU0] (supports C1 C2, 2 throttling states)
PCI: Setting latency timer of device 0000:00:11.5 to 64
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
nvidia: no version for "struct_module" found: kernel tainted.
nvidia: module license 'NVIDIA' taints kernel.
0: nvidia: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-5336 Wed
Jan 14 18:29:26 PST 2004
agpgart: Unknown parameter `agp_try_unsupported'
0: NVRM: AGPGART: unable to retrieve symbol table
Linux video capture interface: v1.00
bttv: driver version 0.9.12 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 0000:00:0b.0, irq: 19, latency: 32, mmio:
0xe2005000
bttv0: detected: Leadtek WinFast TV 2000 [card=34], PCI subsystem ID is
107d:6606
bttv0: using: Leadtek WinFast 2000/ WinFast 2000 XP
[card=34,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00bff707 [init]
i2c-algo-bit.o: (0) scl=1, sda=1
i2c-algo-bit.o: (1) scl=1, sda=0
i2c-algo-bit.o: (2) scl=1, sda=1
i2c-algo-bit.o: (3) scl=0, sda=1
i2c-algo-bit.o: (4) scl=1, sda=1
i2c-algo-bit.o: bt878 #0 [sw] passed test.
bttv0: using tuner=5
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tuner: chip found at addr 0xc2 i2c-bus bt878 #0 [sw]
tuner: type set to 5 (Philips PAL_BG (FI1216 and compatibles)) by bt878
#0 [sw]
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
bttv0: add subdevice "remote0"
atkbd.c: Unknown key released (translated set 2, code 0x7a on
isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
NET: Registered protocol family 4
and so on .... 